1. Home
  2. All Products
  3. Wireless Lighting Solutions
  4. 22231 - LA-WLBx2RM-6-24 LitezAll RC Wireless Light Bar 2 Pack
22231 - LA-WLBx2RM-6-24 LitezAll RC Wireless Light Bar 2 Pack
22231 - LA-WLBx2RM-6-24 LitezAll RC Wireless Light Bar 2 Pack

22231 - LA-WLBx2RM-6-24 LitezAll RC Wireless Light Bar 2 Pack

Your Price: $14.99
SKU: 22231
Availability: In Stock. 3829
Mfg. Part # LA-WLBx2RM-6-24
Display Dimensions HxWxD 10.25" x 8" x 9.75"
Package Dimensions HxWxD 9.25" x 6.75" x 1.25"
Inner/Master Carton Qty: 6/24
UPC 8-11446-02223-1

22231 - LitezAll RC Wireless Light Bar 2 Pack

LitezAll super convenient and bright wireless light bar but with added remote control capability. Enjoy up to 200 lumens of bright, shadow free light plus a battery savibng low brightness mode.

Peel and stick metal disc is included and may be applied to just about any smooth surface to take advantage of the strong magnet built into the light bar. Light bars install magnetically to most smooth metal surfaces without the disc. Keyhole mounts built-in to facilitate a more permanent installation.

As with many of LitezAll Wireless Lighting Solutions, this light may be used as a Grab and Go® light for added convenience.
  • 200 Max Lumens (Each Light)
  • Remote Control or Push Button On/Off. Choose from 200 Lumens or 100 Lumens
  • S.O.S. Mode for Emergency Visibility
  • Energy Efficient COB LED Light
  • Mounts Easily with Magnet or Keyhole Mounts
  • Peel and Stick Metal Disc Included to Create a Metal Surface Anywhere
  • Elegant Appearance
  • Runs on 3 AAA Batteries ( 6 Batteries included)
  • Each Wireless Light Bar Measures 6.25" long x 1.25" wide x 1.5" high

INSTALLATION: Select a clean non-porous surface where you would like to mount the light. Carefully remove the backing from the peel and stick metal mounting disc (disc may be attached to the magnet on the back of the light). Place the disc in the desired location and press firmly for 30 seconds. Wait 24 hours before attaching the light magnetically to the disc. WARNING: MOUNTING DISC CANNOT BE REMOVED EASILY ONCE INSTALLED!

ACTIVATE THE REMOTE: The remote is activated by turning the lights on manually one time (via the light, not the remote). Once the lights are turned on, you can use the remote to turn the lights off and on. Remote control operation will continue until the batteries in the lights or remote need replacing. After changing the batteries, repeat the first step to activate the remote once again.

IMPORTANT: If you will not be using this light for up to 30 days, you should set the mode switch to the "OFF" position. For longer periods of time, such as storage, remove the batteries to prevent damage or drain.


To replace batteries in lights, remove the battery cover, remove old batteries and insert 3 new AAA alkaline batteries with the negative end first, replace cover. Replace all batteries at the same time.

To replace the battery in remote, slide open battery tray, remove the old battery and insert 1 new CR2025 battery, reinsert battery tray.

Caution: Replace all batteries at the same time. Do not install batteries backwards, charge or put in fire. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cd, Ni-MH, etc.) batteries. This may cause batteries to leak or explode. Old or discharged batteries must be recycled or disposed of properly.

Warning! To prevent serious injury, including temporary or permanent loss of sight do not stare into the light, shine light into eyes or focus the beam using an additional lens. Keep away from infants and toddlers as this product contains small parts.

This product is not a toy! Use this light only as it is intended. Inspect before every use, do not use if parts are damaged, loose or missing.

Save these safety precautions.